Linear drain Wiper 700 mm Elite Ponente

Wet room drainage Wiper Elite Ponente 700 mm

is the best quality stainless steel gully in our store. It features flange connection drainage which allows water trapped under tiles to be taken out of shower. Grating is also advanced, it has integrated system which allows to set up height from 8 mm up to 50 mm. Floor level Elite drain has low installation height, modern beautiful design and good technical properties makes it a luxury product.

Linear drain Elite is 52 mm wide and comes with included Ponente grate type. It is plain stainless steel bar without any holes, only channels aside. That's the only visible part after the installation is completed. Frame is 12 mm high so is maximum thicknes for finish material plus adhesive. Modern and convenient design with practicality for everyday use item. Total width with insulating flange is 96 mm and total unit length 740 mm.

Appropriate Smart Trap high capacity siphon trap is integrated to the gully, centred with pipe stuck in 90 degrees angle. Pipe is 40 mm long and has diameter of 40 mm with included adapter which allows it to be connected to 50 mm waste system pipe. Trap has 30 mm tall water seal which blocks the air from going back to bathroom. It features capacity of 38 l / min and can be installed in wet room with even large shower heads.

More details

New

£ 239.35

Tax included

£ 299.19

-20%

  • Not include
  • 3 m²
  • 6 m²
Waterproofing kit is used to seal shower tray as well as connections between walls and floor. It is recommended for concrete and mandatory for timber flooring. Each kit contains: 4kg tanking liquid, 1l primer, 10m sealing tape, 2 corners, 2 pipe collars. One kit covers 3 m² with 2 coats. If you buy it as addition to any drain or wet room kit You save £40 if you buy kit that covers 3 m² or £80 if buy one which covers 6 m².

Save for later

Question will be displayed after moderation.
Send to a friend

Product information will be sent to given address.

* Required fields

Cancel

Channel length700 mm
Grate stylePonente
Channel height18 - 60 mm
Total height64 mm
Channel width48 mm
Total width90 mm
Material304 S 15 grade stainless steel
Set consistsLinear drain body · stainless steel collar · sealing membrane · drain grating · stainless steel siphon trap
AdditionalsTanking kit, Adjustable legs
Drain surfacemirror · brush · matt
SiphonStainless steel
Steel collarIntegrated
CleaningFrom above (Easy clean system)
ModelElite
  • Length (X): 700 [mm]
  • Total height (H): 64 [mm]
  • Width of channel (Y): 48 [mm]
  • Width of insulating flange (F): 90 [mm] (included)
  • Width of sealing membrane (M): 250 [mm] (included)
  • Flange to top edge of channel (T): 8 - 50 [mm] (adjustable)
  • Complete stainless steel siphon, pipe diameter: 1.5" (british standard size),
  • Drain's cover included.

Premium Slim technical drawing

Product is suitable for:
Timber floor Concrete floor Tiles Mosaic

Grating patterns available for this product:

Linear shower drain advantages


Adjustable legsAdjustable feet are two small metal parts that can be connected to each channel end. They allow you to set the unit height when installing down the concrete floor. It can be easily removed if necessary for installation in timber floor.

They are part of unit, included in price and always added to each drain.

The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.

For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.

Tanking kit contains:

  • 4kg Tanking Liquid
  • 1l Primer
  • 10 Metres flexible Sealing Tape
  • 2 Flexible Pipe Collars
  • 2 Corners

Features:

  • Consumption to 1,2kg/m²
  • Solvent free
  • Drying time: 2h

Tanking liquid

Tanking liquidThe tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.

Primer

Tanking primerThe product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.

10m sealing tape · 2x flexible pipe collars · 2x corners

Tanking mattPipe collarCorner

The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.


Sealing membrane

The drain includes a new patented SMART TRAP® stainless steel siphon with a capacity of 38 l/min and the Easy Clean system. To clean it you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals. The waste trap provides Water Seal that prevents any bad smells to get back to your shower.



  • Colour: metal, chrome
  • Material: 304 stainless steel,
  • Cleanable: from above,
  • Smell trap: incorporated,
  • Pipe diameter: 1,5" (british standard pipe size),
  • Diameter of siphon: 105 mm,
  • Total siphon height: 50 mm.

Caution. Please read the instructions carefully before installation.


  • The diagram shows various parts of the channel and their dimensions can be found on the More info tab.
  • We recommend that you do not remove the protective foil from the grating until the installation is complete
  • The instructions refer to the correct installation of the channel only and do not include information regarding insulation or other elements of the shower cabin such as sealing connections between the shower walls and floor as well as water proofing.
  • The channel should be installed together with the siphon trap and then the adjustable legs should be glued in the places shown.

Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.

Wiper Premium Slim installation Wiper Premium Slim technical drawingLong term guarantee

30 Similar products