mm is the lowest profile wet room drainage type we can supply. It's total height including waste trap is only 64 mm. Channel consists of flange and welded vertical frame. Modern design, slim grating and low space requirements are making it suitable and good looking in almost every shower. High capacity, welded siphon trap is integrated with the drainage. A textile sealing membrane is also included, allowing to achieve waterproof seal very easily.
Premium Slim drain channel is 52 mm wide and it has included Pure slot grate which is 38 mm wide. Tileable grate depth is 12 mm, so tiles should not be thicker than 10 mm. After tiling is completed only visible part of the drain is gap between the grate and rest of the floor, which allows water to flow. Total width with insulating flange is 96 mm and total unit length 540 mm.
Stainless steel waste trap is welded below the drainage, is fixed in position with outlet perpendicular to channel. Outlet is 40 mm long and has diameter of 40 mm, comes with adapter which allows you to connect it to 50 mm standard pipes. It is high flow rate siphon trap which can take up to 38 l/min. Water seal of 30 mm stops the smells from getting back into shower. Easy clean system gives access from cleaning from above, after lifting up the grate.
Linear drain body · stainless steel collar · sealing membrane · drain grating · stainless steel siphon trap
Length (X): 500 [mm]
Total height (H): 70 [mm]
Width of channel (Y): 54 [mm]
Width of insulating flange (F): 97 [mm] (included)
Width of sealing membrane (M): 250 [mm] (included)
Flange to top edge of channel (T): 12 [mm]
Complete stainless steel siphon, pipe diameter: 1.5" (british standard size),
Sipon trap rotatable at 360°,
Drain's cover included.
Pure drain cover is an internal container that you can insert the tiles into. This type of drain is 100% tile-able.
Tile channel depth (A): 12 [mm]
Tile channel width (D): 50 mm [mm]
Product is suitable for:
Timber floorConcrete floorTilesMosaic
Grating patterns available for this product:
Adjustable feet are two small metal parts that can be connected to each channel end. They allow you to set the unit height when installing down the concrete floor. It can be easily removed if necessary for installation in timber floor.
They are part of unit, included in price and always added to each drain.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
Tanking kit contains:
4kg Tanking Liquid
10 Metres flexible Sealing Tape
2 Flexible Pipe Collars
Consumption to 1,2kg/m²
Drying time: 2h
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
The drain includes a new patented SMART TRAP® stainless steel siphon with a capacity of 38 l/min and the Easy Clean system. To clean it you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals. The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
Colour: metal, chrome
Material: 304 stainless steel,
Cleanable: from above,
Smell trap: incorporated,
Pipe diameter: 1,5" (british standard pipe size),
Diameter of siphon: 105 mm,
Total siphon height: 50 mm.
Tiled floor surface,
Caution. Please read the instructions carefully before installation.
The diagram shows various parts of the channel and their dimensions can be found on the More info tab.
We recommend that you do not remove the protective foil from the grating until the installation is complete
The instructions refer to the correct installation of the channel only and do not include information regarding insulation or other elements of the shower cabin such as sealing connections between the shower walls and floor as well as water proofing.
The channel should be installed together with the siphon trap and then the adjustable legs should be glued in the places shown.
Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.