is stainless steel shower gully without vertical frame, which gives it flexibility to be installed under any finish material. It is most commonly used to be in vinyl, marble, stone, exotic wood or glass floorings. Entire drain including the grating should be covered with your finish material so only channels for water to flow are visible after installation. Invisible Slim is more advanced than Invisible, it has lower installation height and higher capacity. Wet room drains Invisible have included grate 52 mm wide and total width with flange is 92 mm. Cover is 494 mm long and drain 560 mm long in total. It should be covered entirely with floor finish material, best if it's edges could be properly adapted to leave sufficient amount of space for gaps for water to flow. Fabric for cleaning purposes before sticking finish material to cover is included. Stainless steel waste trap is welded below the drainage, is fixed in position with outlet perpendicular to channel. Outlet is 40 mm long and has diameter of 40 mm, comes with adapter which allows you to connect it to 50 mm standard pipes. It is high flow rate siphon trap which can take up to 38 l/min. Water seal of 30 mm stops the smells from getting back into shower. Easy clean system gives access from cleaning from above, after lifting up the grate.See parts included
Warning: Last items in stock!
1.2 mm thick steel
For fitting and using
Size: not included
|Channel length||500 mm|
|Channel height||20 mm|
|Total height||68 mm|
|Channel width||52 mm|
|Total width||90 mm|
|Material||304 S 15 grade stainless steel|
|Additionals||Tanking kit, Adjustable legs|
|Shower waste||Stainless steel|
|Cleaning||From above (Easy clean system)|
|Set consists||Linear drain body · stainless steel collar · sealing membrane · drain grating · siphon trap|
Adjustable feet are two small metal parts that can be connected to each channel end. They allow you to set the unit height when installing down the concrete floor. It can be easily removed if necessary for installation in timber floor.
They are part of unit, included in price and always added to each drain.
The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
The drain includes a new patented SMART TRAP® stainless steel siphon with a capacity of 38 l/min and the Easy Clean system. To clean it you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals. The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
Typical questions asked about products:
How long is the delivery?
Is the product easy to fit?
Which options should I choose?