The SIEME linear drains are a series of elegant and durable, high-quality drainage systems. They are finished with an elegant frame and stainless steel grate with a width of 70 mm. The drains come in length of 700 mm. The product can be customized to match individual needs and tastes of the customers.
The STEEL drain is equipped with a perforated shiny stainless steel grill.
Warning: Last items in stock!
Main drainage part, stainless steel channel drain, 30 mm high, 70 mm wide. Outlet is centred. Surrounded by steel flange on all four sides, 30 mm wide, important for insulation.
1 mm thick steel
Compression fitting McAlpine waste trap with 26 l/min throughput, 20 mm water seal and 1.5 inch pipe diameter. Requires only 65 mm of space underneath the tray. Fully rotatable and adjustable.
Flow rate: 26 l/min
Product is supplied as complete set. Adjustable feet are very helpful to position to drain at proper level and are easily removable for installation in timber floor. Sealing membrane included to waterproof the channel. Lifting hook for drain grating and other fitting parts also in the package.
For fitting and using
Easy to use set of ready-mixed sealing materials suitable for waterproofing floor and walls. Contains 4kg of PCI Lastogum tanking paint, 1l of primer, 10m sealing tape, 2 corners and 2 pipe collars per 3 m². Should be used to seal the joints between the floor and walls and to waterproof the drainage. Can be used for entire bathroom insulation. Not required if you have your own waterproofing materials, otherwise very useful and recommended.
Size: not included
|Channel length||700 mm|
|Channel height||30 mm|
|Total height||100 mm|
|Channel width||70 mm|
|Total width||109 mm|
|Material||304 S 15 grade stainless steel|
|Drain surface||mirror · brush · matt|
|Waste trap||Plastic (PCV)|
|Cleaning||From above (Easy clean system)|
|Set consists||Linear drain body · stainless steel collar · sealing membrane · drain grating · Adjustable legs · siphon trap|
The MATLASTIC mat is made of polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer better. Its installation is recommended in all areas that require sealing. The MATLASTIC mat is lightweight, flexible and resistant to decay, it ensures a uniform thickness of the sealing layer, it is resistant to cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
A tanking kit is used to insulate the surface on which tiles will be laid, in areas exposed to moisture. It is recommended wherever a high degree of water resistance is required and in places with high humidity (eg, showers, bathrooms, toilets, laundries, kitchens, etc.). Waterproofing can be used on any type of substrate: the walls of the gypsum-carton boards (Rigips), plastered walls, walls of concrete blocks, wood-based materials, old ceramic tiles, old stone cladding, etc.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
The Matlastic mat is made of polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer better. Its installation is recommended in all areas that require sealing. The MATLASTIC mat is lightweight, flexible and resistant to decay, it ensures a uniform thickness of the sealing layer, it is resistant to cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
Typical questions asked about products:
How long is the delivery?
Is the product easy to fit?
Which options should I choose?