is the most popular linear drainage type. Length of 500 mm gives a lot of flexibility with installation and design of your wet room. It is made of 304 stainless steel which offers good corrosion resistance to both chemical and atmospheric exposures, with a high resistance to oxidation. It is surrounded by 30 mm wide steel flange and sealing membrane which are very useful especially in timber floors, although drain is also suitable for concrete flooring. This is perfect gully for tiled floors, as the lip height is 15 mm.
Premium drain channel is 84 mm wide, while it comes with included Sirocco which is considered to be the most practical pattern, with 3 rows of square shaped holes running parallelly to cover edge and 64 mm wide, grate is 494 mm long and total drain length with insulation flange is 560mm. Sealing membrane is a blue non-woven fabric which bonds well in the glue and is resistant to cracking.
65 mm high McAlpine siphon trap with pipe is also included to drain. It features capacity of 26 l /min and water seal 20 mm high. Trap can be opened from above, even after the installation is completed, after lifting up the grate to allow easy cleaning. Standard 1.5'' pipe is in the same pack, allowing instant connection to your waste system.
Warning: Last items in stock!
1.2 mm thick steel
Flow rate: 26 l/min
For fitting and using
Size: not included
|Channel length||500 mm|
|Channel height||30 mm|
|Total height||98 mm|
|Channel width||84 mm|
|Total width||140 mm|
|Material||304 S 15 grade stainless steel|
|Additionals||Tanking kit, Adjustable legs|
|Drain surface||mirror · brush · matt|
|Waste trap||Plastic (PCV)|
|Cleaning||From above (Easy clean system)|
|Set consists||Linear drain body · stainless steel collar · sealing membrane · drain grating · siphon trap|
Adjustable feet are two small metal parts that can be connected to each channel end. They allow you to set the unit height when installing down the concrete floor. It can be easily removed if necessary for installation in timber floor.
They are part of unit, included in price and always added to each drain.
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
I need linear drain for wet room. Suitable for mounting on wooden floor with support beams and tanked plywood. The Premium Sirocco looks a good choice, but it doesn't have mounting feet. How do you advise supporting? Thanks.
Premium Sirocco is the most popular and most versatile drainage type suitable for wet room. We also carry largest amount of them in our warehouse so they are available for quick delivery.
They do come as a complete product with all parts included. Adjustable feet are always added to the product. If installed on timber flooring it probably doesn't require adjustable feet. You could just cut the hole in the ply and insert the drain there.