is the most popular linear drainage type. 600 mm is the second shortest length, common for most wet rooms. It is made of 304 stainless steel, which offers good corrosion resistance to both chemical and atmospheric exposures, with a high resistance to oxidation. It is surrounded by a 30 mm wide steel flange and sealing membrane, which are very useful, especially in timber floors, although a drain is also suitable for concrete flooring. This is a perfect gully for tiled floors, as the lip height is 15 mm.
Premium drain channel is 84 mm wide, while it comes with the, included, Pure tile able grate. The channel is 12 mm deep and 64 mm wide, while the grate is 594 mm long and total drain length, with insulation flange, is 660mm. The slot drain should be filled with tiles, so at the end of the day, only the visible part of the drain should be the channel, which water flows through. The sealing membrane is a blue, non-woven fabric which bonds well with the glue and is resistant to cracking.
Sufficient siphon trap is made by McAlpine, with a capacity of 26 l/min and a 20 mm high water seal is included with the drain. The flow rate is comfortable for a single shower head and the seal protects smells from getting back into your shower. It comes with a pipe so it can be easily connected to every standard waste system. The siphon can be accessed from above, even after installation, allowing to clean the drain easily.
Warning: Last items in stock!
Main drainage part, stainless steel channel drain, 30 mm high, 84 mm wide. Outlet is centred. Surrounded by steel flange on all four sides, 30 mm wide, important for insulation.
1.2 mm thick steel
Compression fitting McAlpine waste trap with 26 l/min throughput, 20 mm water seal and 1.5 inch pipe diameter. Requires only 65 mm of space underneath the tray. Fully rotatable and adjustable.
Flow rate: 26 l/min
Product is supplied as complete set. Adjustable feet are very helpful to position to drain at proper level and are easily removable for installation in timber floor. Sealing membrane included to waterproof the channel. Lifting hook for drain grating and other fitting parts also in the package.
For fitting and using
Easy to use set of ready-mixed sealing materials suitable for waterproofing floor and walls. Contains 4kg of PCI Lastogum tanking paint, 1l of primer, 10m sealing tape, 2 corners and 2 pipe collars per 3 m². Should be used to seal the joints between the floor and walls and to waterproof the drainage. Can be used for entire bathroom insulation. Not required if you have your own waterproofing materials, otherwise very useful and recommended.
Size: not included
|Channel length||600 mm|
|Grate style||Pure (slot)|
|Channel height||30 mm|
|Total height||98 mm|
|Channel width||84 mm|
|Total width||140 mm|
|Material||304 S 15 grade stainless steel|
|Additionals||Tanking kit, Adjustable legs|
|Drain surface||mirror · brush · matt|
|Waste trap||Plastic (PCV)|
|Cleaning||From above (Easy clean system)|
|Set consists||Linear drain body · stainless steel collar · sealing membrane · drain grating · siphon trap|
Pure drain cover is an internal container that you can insert the tiles into. This type of drain is 100% tile-able.
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
Adjustable feet are two small metal parts that can be connected to each channel end. They allow you to precisely set the unit height and level. Thanks to the red caps you can anchor the drain to the floor. They are part of unit, included in price and always added to each drain.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
FOR THE LINEAR DRAIN, HOW CAN I ORDER A PLAIN TILABLE COVER, AND A SCIRROCO VERSION TOO ON LINE PLS?
I would like to confirm that grating patterns are interchangeable and can be swapped even after installation is done. There's even possibility to have multiple covers for a single channel.
At the moment it is not possible to order gratings separately on our website, please contact us and we'll prepare an offer for you.
We will need delivery address, billing address (if different) and then we'll send you link for payment.
If you have any questions please contact me.
David 020 7193 0953
Have you got 30 of those drains in stock for next week delivery to London? My main supplier can't realize order for us on time we're looking for alternative company. Prompt reply would be appreciated.
I've just verified with our warehouse how many of Premium Pure 600 mm drains we've got and can confirm that we have them available for next day delivery.
If you're interested in receiving them on Monday please send us an email to firstname.lastname@example.org with exact quantity (we've got some more than 30 which you specified) your company information and delivery address postcode. We will reply with trade discount voucher as such order qualifies for personalised offer.
There's even possibility to deliver them tomorrow (on Saturday), but delivery would not be free in that case. It would cost approximately £75 to have 30 of them delivered tomorrow.
Order has to be placed before 3pm as we need some time for preparations and packaging.
Looking forward to hearing from you.
David 020 7193 0953
These drains are available in our warehouse with next day delivery. If you place the order before 3 o'clock you will receive the goods on next business day.
Let me know if you have any questions.
017 0927 3601
Do you sell the trap inserts for the wiper this wiper drain?
We are able to supply a complete waste trap replacement, you would be able to take that waste trap from it and insert it to your drain.
Price of a new waste siphon trap is £25.
Please contact me and I will help you to place the order.
Adam 017 0927 3601
What are your office opening hours ?Are you open on an Saturday please ?
We are not working during weekends, sometimes we do reply to emails and phone calls.
You can visit our Rotherham warehouse from Monday to Friday, 9am - 6 pm.
Let me know if you have any questions about our products or service.
Adam 017 0927 3601
This drain is surrounded by stainless steel flange, which extends it's size by 30 mm on all four sides. Therefore you would have a small space in between the wall and the drain's edge.
If you could gring a hole in your wall and insert the flange there then yes, it could be installed right next to the wall.
Alternatively we could supply this drain with upstand flange, this would be bespoke product, with increased price and delivery time. More details together with quote has been sent to your email address.
I am happy to assist if you have any questions.