Linear drain Wiper 500 mm Invisible

Floor level drain Wiper Invisible 500 mm

is stainless steel shower gully without vertical frame, which gives it flexibility to be installed under any finish material. It is most commonly used to be in vinyl, marble, stone, exotic wood or glass floorings. Entire drain including the grating should be covered with your finish material so only channels for water to flow are visible after installation. It comes with insulating flange and sealing membrane which allow to achieve 100% waterproof seal.

Wet room drains Invisible have included grate 80 mm wide and total width with flange is 140 mm. Cover is 494 mm long and drain 560 mm long in total. It should be covered entirely with floor finish material, best if it's edges could be properly adapted to leave sufficient amount of space for gaps for water to flow. Fabric for cleaning purposes before sticking finish material to cover is included.

65 mm high McAlpine siphon trap with pipe is also included to drain. It features capacity of 26 l /min and water seal 20 mm high. Trap can be opened from above, even after the installation is completed, after lifting up the grate to allow easy cleaning. Standard 1.5'' pipe is in the same pack, allowing instant connection to your waste system.

More details

New

£ 153.25

Tax included

£ 191.57

-20%

  • Not include
  • 3 m²
  • 6 m²
Waterproofing kit is used to seal shower tray as well as connections between walls and floor. It is recommended for concrete and mandatory for timber flooring. Each kit contains: 4kg tanking liquid, 1l primer, 10m sealing tape, 2 corners, 2 pipe collars. One kit covers 3 m² with 2 coats. If you buy it as addition to any drain or wet room kit You save £40 if you buy kit that covers 3 m² or £80 if buy one which covers 6 m².

Save for later

Question will be displayed after moderation.
Send to a friend

Product information will be sent to given address.

* Required fields

Cancel

Channel length500 mm
Grate styleInvisible
Channel height20 mm
Total height88 mm
Channel width80 mm
Total width140 mm
Material304 S 15 grade stainless steel
AdditionalsTanking kit, Adjustable legs
Drain surfacebrush
SiphonPlastic (PCV)
Steel collarIntegrated
CleaningFrom above (Easy clean system)
ModelInvisible
Set consistsLinear drain body · stainless steel collar · sealing membrane · drain grating · siphon trap
  • Length (X): 500 [mm],
  • Height of channel (C): 20 [mm],
  • Height to the centre of waste pipe (G): 58 [mm] (can be adjusted),
  • Total height (H): 88 [mm],
  • Width of internal tray (B): 70 [mm],
  • Width of channel (Y): 80 [mm],
  • Width of insulating flange (F): 140 [mm] (included)
  • Width of Sealing Membrane (S): 250 [mm] (included)
  • Flange to top edge of channel (T): 15 [mm]
  • Complete siphon, pipe diameter: 1.5" (british standard size),
  • Pipe height adjustable and rotatable at 360°,
  • Drain's cover included.

Product is suitable for:
Timber floor Concrete floor
Vinyl
Hardened glass
Gres
Granit
Marble
Exotic wood
Tiles
Mosaic

Linear shower drain advantages


Adjustable legsAdjustable feet are two small metal parts that can be connected to each channel end. They allow you to set the unit height when installing down the concrete floor. It can be easily removed if necessary for installation in timber floor.

They are part of unit, included in price and always added to each drain.

The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.

For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.

Tanking kit contains:

  • 4kg Tanking Liquid
  • 1l Primer
  • 10 Metres flexible Sealing Tape
  • 2 Flexible Pipe Collars
  • 2 Corners

Features:

  • Consumption to 1,2kg/m²
  • Solvent free
  • Drying time: 2h

Tanking liquid

Tanking liquidThe tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.

Primer

Tanking primerThe product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.

10m sealing tape · 2x flexible pipe collars · 2x corners

Tanking mattPipe collarCorner

The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.


Sealing membrane

We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals. 

The waste trap provides Water Seal that prevents any bad smells to get back to your shower.

  • Colour: white,
  • Total height: 61,50 mm,
  • Waste pipe diameter: 1.5" (british standard size)
  • Water seal: 20mm
  • Flow rate [l/min]: 26/50 (for a 15mm/120mm liquid column)
  • Ready to be connected to waste system
  • Additional info: Waste Grid and Dip Tube removable from top to facilitate easy cleaning. All McAlpine Shower Traps with top access surpass the minimum required flow rate of 24 litres per minute when tested in accordance with clause 5 of BS EN 274-2:2002

Suitable for:

  • Wet rooms,
  • Showers,
  • Bathrooms,
  • Wooden floors,
  • Mosaic floors,
  • Concrete floors,
  • Screed floors,
  • Vinyl flooring,
  • Stone, granit,
  • Marble, gres
  • Exotic wood
  • Hardened glass
  • Tiled floor surface,

Caution. Please read the instructions carefully before installation.


  • The diagram shows various parts of the channel and their dimensions can be found on the More info tab.
  • We recommend that you do not remove the protective foil from the grating until the installation is complete
  • The instructions refer to the correct installation of the channel only and do not include information regarding insulation or other elements of the shower cabin such as sealing connections between the shower walls and floor as well as water proofing.
  • The channel should be installed together with the siphon trap and then the adjustable legs should be glued in the places shown.

Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.

Wiper Invisible installation Wiper Invisible technical drawingSiphon technical drawing  Long term guarantee