Wet room Kit Showerlay Wiper 900 x 900 mm Line Invisible
is a walk in shower tray with end linear drain. Board can be 20, 30 or 40 mm thick, is sloped towards the drain, provides great acoustic insulation and is also lightweight while very strong. It is suitable both for concrete and timber floors. Shower area should be covered entirely, including drain grating, with finish material. The only visible features are the gaps in the floor through which the water drains
Suitable shower drainage is included to former, it comes with 600 mm long steel linear end drain. It also comes with grating which is 70 mm wide, leaving 8 mm wide channel for water to flow. Grate is flushed with the frame, so there is no requirement for finish material height, although channel protrudes below the bottom shower tray surface for 10 mm. Steel is finished with brush, which is practical and particularly suitable for most architectural applications. Special degreasing cloth is included to clean the steel surfaces before gluing the finished floor surface. McAlpine siphon trap with capacity of 26 l/min and 20 mm high water seal is also included. Showerlay is complete unit with everything you need.
Wet room kit 900 x 900 mm is second smallest square tray former in our store. Save space with wetroom, with the average UK bathroom not much bigger than a king-sized bed, a wet room can be an ideal space-saving solution.
Wet room tray · integrated linear drain body · drain grating · siphon trap
From above (Easy clean system)
Dimensions as described on equivalent technical drawings,
Both sides can be trimmed without any harm, using regular handsaw,
Make sure you cut it for equal distances from both sides to preserve pre-made fall to the drain,
Drain channel is located centrally, across the shorter edge.
Designed especially for range of Wiper Premium drains,
Drain is built into the tray during the manufacturing process,
Our showerlay is a 20/30/40 mm XPS foam sheet covered on both sides with a flexible cementous glue and reinforced with a fibre glass mesh,
The showerlay is CNC machine cut to give a perfect pre-formed fall from each corner to the drain,
It is lightweight but very strong,
Perfect solution for British wooden floors but can also be used on concrete floors. When it is used on wooden floors,the floor must be underboarded after floor boards have been removed,
Standard and minimal underboarding should be 20 mm thick,
Suitable for large range of finish materials, from safety floorings and vinyl sheets to marble and thick stone. Frame completely flushed with the shower tray level allow to any material that can be aesthetically finished suitable for this product.,
The shower lay can be easily cut on site should you have any obstacles such as pipe boxings,
Easy to use with under floor heating systems,
One hundred per cent, double waterproofing,
Hardness of the surface layer allows to cement even very small mosaics,
High acoustic insulation,
Increased mat size in relation to the plate enabling good sealing with walls and floors,
After installation, the plates should be supported over theentire surface.
Product is suitable for:
Timber floorConcrete floor
Our wet room kits are available in three thicknesses: 20, 30 and 40 mm. Depending on space, floor type, and desired gradient you can choose best option for you.
If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 40 mm thickness might also be a good choice . Wet room kit timber floor fitting instructions
If case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions
In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
Tanking kit contains:
4kg Tanking Liquid
10 Metres flexible Sealing Tape
2 Flexible Pipe Collars
Consumption to 1,2kg/m²
Drying time: 2h
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
Total height: 61,50 mm,
Waste pipe diameter: 1.5" (british standard size)
Water seal: 20mm
Flow rate [l/min]: 26/50 (for a 15mm/120mm liquid column)
Ready to be connected to waste system
Additional info: Waste Grid and Dip Tube removable from top to facilitate easy cleaning. All McAlpine Shower Traps with top access surpass the minimum required flow rate of 24 litres per minute when tested in accordance with clause 5 of BS EN 274-2:2002