Showerlay Wiper 900 x 1850 mm Line Zonda

46900

Delivery:Free | 1-3 working days
Payment:Card | Over the phone | PayPal | BACS
Returns:30 days return right
Support:020 7193 0953 • 017 0927 3601

£ 368.04

tax incl.

£ 432.99 tax incl. -15%

Trade discount policy:bulk orders and returning customers

Save for later

Send to a friend

Send product information

Basic product info and a link to a product will be sent to a person specified above.

Where should we reply to?

We will do our best to reply as fast as possible.

Wet room Kit Showerlay Wiper 900 x 1850 mm Line Zonda is a walk in shower tray with end linear drain. Former is available in three thicknesses, has 2% fall towards the drain, provides great acoustic insulation and is also lightweight while very strong.

Suitable shower drainage is included to former, it comes with 600 mm long steel linear end drain. It also comes with grating which is 64 mm wide, leaving 8 mm wide channel for water to flow. Zonda is a grill with angled rectangles across the entire top cover. Height from the shower tray surface to the top edge of vertical upstand is 15 mm, it also goes below the tray for approximately 5 mm. McAlpine siphon trap with capacity of 26 l/min and 20 mm high water seal is also included. Showerlay is complete unit with everything you need.

Larget wet room kit 900 x 1850 mm is shower tray that can be installed in rooms with very large amounts of space. A walk in shower flooring opens up the bathroom and adds modern simple and fresh look creating a more attractive restroom. It offers people with mobility issues easy accessibility. Showerlay of that size is particulary suitable for large tiles format, although it can still be laid with even small mosaic.

If you buy this product you will receive (parts included):

Size900 x 1850 mm
Channel length600 mm
Grate styleZonda
Height1850 mm
Width900 mm
Thickness20 · 30 · 40 mm
TrimmingShorter side: up to 50 mm · Longer: up to 100 mm.
MaterialXPS foam sheet
ReinforcementFibre glass mesh & cementous glue.
Fall4-way 2% towards the drain
AdditionalsTanking kit
Drain surfacebrush
CleaningFrom above (Easy clean system)
ModelLine
Set consistsWet room tray · integrated linear drain body · drain grating · siphon trap
  • Dimensions as described on equivalent technical drawings,
  • If needed, the tray can be easily shortened in its length or width, using a handsaw,
  • Make sure you cut it for equal distances from both sides to preserve pre-made fall to the drain,
  • Drain channel is located centrally, across the shorter edge.
  • Designed especially for range of Wiper Premium drains,
  • Drain is built into the tray during the manufacturing process,
  • Our showerlay is a 20/28/35 mm XPS foam sheet covered on both sides with a flexible cementous glue and reinforced with a fibre glass mesh,
  • The showerlay is CNC machine cut to give a perfect pre-formed fall from each corner to the drain,
  • It is lightweight but very strong,
  • Perfect solution for British wooden floors but can also be used on concrete floors. When it is used on wooden floors,the floor must be underboarded after floor boards have been removed,
  • Standard and minimal underboarding should be 20 mm thick,
  • Ideal for tiled floors. Because of the high compressive strength of the XPS foam, it can even be used with small mosaic tiles. This is not suitable for vinyl floor coverings,
  • The shower lay can be easily cut on site should you have any obstacles such as pipe boxings,
  • Easy to use with under floor heating systems (should be installed on top of the shower tray)
  • One hundred per cent, double waterproofing,
  • Hardness of the surface layer allows to cement even very small mosaics,
  • High acoustic and thermal insulation,
  • After installation, the plates should be supported over the entire surface.
Product is suitable for:
Timber floor Concrete floor Tiles Mosaic

Wet room kit advantages

Our wet room kits are available in three thicknesses: 20, 28 and 35 mm. Depending on space, floor type, and desired gradient you can choose best option for you.

If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 35 mm thickness might also be a good choice. Wet room kit timber floor fitting instructions

In case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions

In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.



Wet room kit 900 x 1850 technical drawing

Shower trays incorporate linear drain built-into the tray during the manufacturing process. Wiper Premium range linear shower drains are made from one peice of 304 grade stainless steel. Only the ends are welded. This means that the flange and drain body are made from the same peice of steel ensuring complete security from water penetration. Our flange is on all four sides of the drain. You will not find a better linear drain on the market.

  • Length (X): 600 [mm]
  • Height of channel (C): 30 [mm]
  • Height to the centre of waste pipe (G): 68 [mm] (can be adjusted)
  • Total height (H): 98 [mm]
  • Width of channel (Y): 84 [mm]
  • Width of insulating flange (F): 140 [mm] (included)
  • Width of sealing membrane (M): 250 [mm] (included)
  • Flange to top edge of channel (T): 15 [mm]
  • Type of surface finish: mirror, matt, brushed
  • High quality Mcalpine poly propylene syphon trap included
  • Easy clean system (cleanable from above)
  • Complete siphon, waste pipe diamter british standard size,
  • Pipe height adjustable and rotatable at 360°,
  • Drain's cover is included, please select desired design.

Grating patterns available for this product:

The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.

For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.

Tanking kit contains:

  • 4kg Tanking Liquid
  • 1l Primer
  • 10 Metres flexible Sealing Tape
  • 2 Flexible Pipe Collars
  • 2 Corners

Features:

  • Consumption to 1,2kg/m²
  • Solvent free
  • Drying time: 2h

Tanking liquid

Tanking liquidThe tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.

Primer

Tanking primerThe product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.

10m sealing tape · 2x flexible pipe collars · 2x corners

Tanking mattPipe collarCorner

Complete Underfloor Heating Kit

It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.

To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.

MAGNUM Underfloor Heating

The MAGNUM Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.

Heating mat

Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.


Underfloor heating mat technical properties:

  • EMC-free 2-conductor cable fitted to fibre-optic net
  • 2.5 meter 3-core supply cable
  • Fully encased in an aluminium earthed sheath
  • Unique blind connection between the heating and the connection cable
  • Chrome/Nickel resistance wire
  • PTFE (Teflon) insulation
  • PVC protective sheath
  • 10 -11 watt per meter resistance wire, 230 Volt
  • Cable diameter approximately 4 mm
  • Mat widths of 25 or 50 cm
  • Complies with current NEN standards for installation in completely wet rooms

Underfloor Heating Mat

Thermostat

In some situations the digital regulation is not required and so the preference is for a simple on/off operation. Specifically industrial applications where the heating must remain on at all times. Therefore MAGNUM has designed the Standard Control: a simple on/off thermostat with temperature regulation that is clearly easy to operate.

Specification:

  • Voltage: 230 Volt - 50/60 Hz
  • Maximum load: 16A / 230 V
  • Temperature range: +5 to +40°C
  • Housing: IP21
  • Color: Polar white (RAL 9010)
  • Testing: CE
  • Technical details:
  • On/off thermostat complete with temperature regulation
  • Including floor sensor
  • Integral room sensor and floor limit sensor
  • Multi frame adapter system for: Gira, Jung, Elko, Merten, Busch Jager, etc.
Underfloor Heating Thermostat

We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals. 

The waste trap provides Water Seal that prevents any bad smells to get back to your shower.

  • Colour: white,
  • Total height: 61,50 mm,
  • Waste pipe diameter: 1.5" (british standard size)
  • Water seal: 20mm
  • Flow rate [l/min]: 26/50 (for a 15mm/120mm liquid column)
  • Ready to be connected to waste system
  • Additional info: Waste Grid and Dip Tube removable from top to facilitate easy cleaning. All McAlpine Shower Traps with top access surpass the minimum required flow rate of 24 litres per minute when tested in accordance with clause 5 of BS EN 274-2:2002

Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.

Showerlay installation 20 mm technical drawing 30 mm technical drawing 40 mm technical drawing Long term guaranteeSiphon technical drawing

Opinions, reviews and tests for:
Showerlay Wiper 900 x 1850 mm Line Zonda
Average grade: 4.5
Ratings number: 2
100% Customers recommend this product.
5
50%
4
50%
3
0%
2
0%
1
0%
Do you own this product?
Leave product review to help other customers to make the right choice

Customer product reviews
Rated 4.50 on the scale 1 - 5 based on 2 customer reviews
Verified purchase

a reliable company

I had to return item due to damage, and I needed it now but great communication and instant refund.

Was this comment useful to you? Yes No
Verified purchase

Love this tray!

Got this piece for myself and I loved it! Value for money ansd also on-time delivery was a plus :)

Was this comment useful to you? Yes No
1
Questions
1
Answers

Question will be displayed after moderation.
I recently bought 3 Shower tray formers from you. The picture on you web-site show the Drain channel standing proud of the surface to allow for tiling. The drainage chanel in the trays you have sent me are flush with the top surface of the former, How am I supposed to finish the tiling. If i tile it as it is then the drain grating will below the top of the tiles? Can you please advise me?

Asked by: John 18-11-2017 21:54:37
1
answer