Your cart
There are no more items in your cart
Showerlay Wiper 900 x 1200 mm Line Pure
Wet room tray 90 x 120 cm for tiled floor with integrated stainless steel linear end drain, waste trap and cover model Pure
25 Reviews
See parts included
Technical specification
Bespoke Wet Room Trays
Wet room Kit Showerlay Wiper 900 x 1200 mm Line Pure is a walk in shower tray with an end linear drain. The former is available in three thicknesses, has a 2% fall towards the drain, provides great acoustic insulation and is also lightweight while very strong.
Suitable shower drainage is included in the former. It comes with a 600 mm long steel linear end drain. It also comes with grating which is 64 mm wide, leaving an 8 mm wide channel for water to flow. Pure is a slot cover that should be filled with tiles, so that, after the installation the only visible part of the tray would be the channel. The height from the shower tray surface to the top edge of the vertical upstand is 15 mm. It also goes below the tray for approximately 5 mm. McAlpine siphon trap with a capacity of 26 l/min and a 20 mm high water seal is also included. Showerlay is a complete unit with everything you need.
Shower kit 900 x 1200 mm is designed to give you a wet room tray for a timber floor level access. It is easy to cut down to size, whilst being lightweight and highly manoeuvrable. The contemporary, minimalist style of wet room will allow your body to rest and your mind rejuvenate.
Based on current settings, if you Add to cart current set and then order, you will receive the following items:
Thickness: 20 mm
Size: not included
-
- Dimensions as described on equivalent technical drawings,
- If needed, the tray can be easily shortened in its length or width, using a handsaw,
- Make sure you cut it for equal distances from both sides to preserve pre-made fall to the drain,
- Drain channel is located centrally, across the shorter edge.
- Designed especially for range of Wiper Premium drains,
- Drain is built into the tray during the manufacturing process,
- Our showerlay is a 20/28/35 mm XPS foam sheet covered on both sides with a flexible cementous glue and reinforced with a fibre glass mesh,
- The showerlay is CNC machine cut to give a perfect pre-formed fall from each corner to the drain,
- It is lightweight but very strong,
- Perfect solution for British wooden floors but can also be used on concrete floors. When it is used on wooden floors,the floor must be underboarded after floor boards have been removed,
- Standard and minimal underboarding should be 20 mm thick,
- Ideal for tiled floors. Because of the high compressive strength of the XPS foam, it can even be used with small mosaic tiles. This is not suitable for vinyl floor coverings,
- The shower lay can be easily cut on site should you have any obstacles such as pipe boxings,
- Easy to use with under floor heating systems (should be installed on top of the shower tray)
- One hundred per cent, double waterproofing,
- Hardness of the surface layer allows to cement even very small mosaics,
- High acoustic and thermal insulation,
- After installation, the plates should be supported beneath entire surface.
Product is suitable for:
Timber floor Concrete floor Tiles Mosaic
- Channel length
- 600 mm
- Grate style
- Pure (slot)
- Height
- 1200 mm
- Width
- 900 mm
- Thickness
- 20 · 30 · 40 mm
- Trimming
- Shorter side: up to 50 mm · Longer: up to 75 mm.
- Material
- XPS foam sheet
- Reinforcement
- Fibre glass mesh & cementous glue.
- Fall
- 4-way 2% towards the drain
- Additionals
- Tanking kit
- Drain surface
- brush
- Cleaning
- From above (Easy clean system)
- Model
- Line
- Set consists
- Wet room tray · integrated linear drain body · drain grating · siphon trap
- Size
- 900 x 1200 mm
5901797276775
Integrated drain
Shower trays incorporate linear drain built-into the tray during the manufacturing process. Wiper Premium range linear shower drains are made from one piece of 304 grade stainless steel. Only the ends are welded. This means that the flange and drain body are made from the same piece of steel ensuring complete security from water penetration. Our flange is on all four sides of the drain. You will not find a better linear drain on the market.
- Length (X): 600 [mm]
- Height of channel (C): 30 [mm]
- Height to the centre of waste pipe (G): 68 [mm] (can be adjusted)
- Total height (H): 98 [mm]
- Width of channel (Y): 84 [mm]
- Width of insulating flange (F): 140 [mm] (included)
- Flange to top edge of channel (T): 15 [mm]
- High quality Mcalpine poly propylene syphon trap included
- Easy clean system (cleanable from above)
- Complete siphon, waste pipe diamter british standard size
- Pipe height adjustable and rotatable at 360°
- Drain's cover is included, please select desired design
- Pure drain cover is an internal container that you can insert the tiles into. This type of drain is 100% tile-able.
- Tile channel depth (A): 12 [mm]
- Tile channel width (D): 60 mm [mm]
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
Tanking kit contains:
Features:
- 4kg Tanking Liquid
- 1l Primer
- 10 Metres flexible Sealing Tape
- 2 Flexible Pipe Collars
- 2 Corners
Features:
- Consumption to 1,2kg/m²
- Solvent free
- Drying time: 2h
Tanking liquid
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
Complete Underfloor Heating Kit
It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.
To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.
SUNFLOOR Underfloor Heating
The SUNFLOOR Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.
Heating mat
Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.
It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.
To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.
SUNFLOOR Underfloor Heating
The SUNFLOOR Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.
Heating mat
Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.
- 2.5 meter 3-core supply cable
- Fully encased in an aluminium earthed sheath
- Unique blind connection between the heating and the connection cable
- Chrome/Nickel resistance wire
- PTFE (Teflon) insulation
- PVC protective sheath
- 10 -11 watt per meter resistance wire, 230 Volt
- Cable diameter approximately 4 mm
- Complies with current NEN standards for installation in completely wet rooms
Thermostat
The C16Wi-Fi is an intuitive programmable thermostat used to control the electrical floor heating system or water heating system. It will keep home comfortable temp whilst minimizing energy use. Install the app on your smartphone to control the heating system remotely with the WiFi thermostat.
Specification:
The C16Wi-Fi is an intuitive programmable thermostat used to control the electrical floor heating system or water heating system. It will keep home comfortable temp whilst minimizing energy use. Install the app on your smartphone to control the heating system remotely with the WiFi thermostat.
Specification:
- Voltage: 230 Volt - 50/60 Hz
- Maximum load: 16A / 3600W
- Temperature range: +5 to +40°C
- IP class: IP21
- Testing: CE
- Cable spec.: ≤ 2,5 mm²
- Standby power: ~ 2W
- Size: 85 x 85 mm
- Integral room sensor and floor sensor
- Colour: white or black
This stylish, colourful and refined digital clock thermostat has been specially designed for electric heating systems. The MAGNUM X-treme Control is supplied with every MAGNUM floor heating set (Mat,Cable and Foil types), including external floor sensor, a built-in air sensor and three different frames that suit most brands of switching equipment. The MAGNUM X-treme Control is simple and intuitive to operate using touch sensitive buttons under the display. The new chameleon function is simple to adapt to the colour of your interior. The stylish screensaver shows the time, temperature and current mode without touching the thermostat. The MAGNUM X-treme Control has a new help function that appears after 10 seconds in the menu with a complete description of the setting in question. The MAGNUM X-treme Control also has a wooden floor function whereby the temperature is limited to 28°C. This makes the MAGNUM X-treme Control the idea and safe solution for every electric heating system.
Specification:
Specification:
- Voltage: 230 Volt - 50/60 Hz
- Maximum capacity: 16A - 3600 watt
- Temperature range: +5 to +40°C
- Frame: IP21
- Color: Polar white (RAL 9010)
- Testing: FI/CE
- Control via touch sensitive keys
- Chameleon function (8 colour themes)
- Screensaver night clock
- Automatic start-up menu
- Slow start-up function
- Wooden floor function (28 °C limit)
- Automatic summer and winter times
- Multi-programme function (2 periods per day)
- Programming multilingual
- Including floor and air sensors
- Multi-frame adapter system for: Gira, Jung, Elko, Merten, Busch Jager, etc.
In some situations the digital regulation is not required and so the preference is for a simple on/off operation. Specifically industrial applications where the heating must remain on at all times. Therefore MAGNUM has designed the Standard Control: a simple on/off thermostat with temperature regulation that is clearly easy to operate.
Specification:
Specification:
- Voltage: 230 Volt - 50/60 Hz
- Maximum load: 16A / 230 V
- Temperature range: +5 to +40°C
- Housing: IP21
- Color: Polar white (RAL 9010)
- Testing: CE
- On/off thermostat complete with temperature regulation
- Including floor sensor
- Integral room sensor and floor limit sensor
- Multi frame adapter system for: Gira, Jung, Elko, Merten, Busch Jager, etc.
Wet room Kit shower tray installation instructions | Timber floor
Wet room Kit shower tray installation instructions | Concrete floor
Our wet room kits are available in three thicknesses: 20, 28 and 35 mm. Depending on space, floor type, and desired gradient you can choose best option for you.
If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 35 mm thickness might also be a good choice. If case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.
Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.
Siphon technical drawing
Showerlay timber floor installation
Showerlay concrete floor installation
20 mm technical drawing
28 mm technical drawing
35 mm technical drawing
Long term guarantee
Siphon technical drawing
25 Reviews
The best
Well made and thought out, exactly what i was looking for
Ok
Exactly what I’ve been looking for!
Ohh nice
Functional and looks good!
Fine!
Surprisingly high quality, installation was really easy, 5/5
Looks good
It looks great in our bathroom & the quality is spot on
Wow
Product as pictured. Good quality.
Good
it's a good looking, nice quality item so I am very satisfied with this purchase. It came way faster then expected
All ok
Bought a second one for the replace bath too.
Superb Quality and Stylish Looks
Great price and great quality. Easy to install and looks the business. Wiper gear is exceptional quality. I have one of their shower drain and that is well built, this wet room tray is of similar quality.
Pleased with the tray
Pleased with the tray.
Easy
Light to carry upstairs and easy to install.
Nice
Very good value for money.
Works well, plumber said it was good quality.
Works well, plumber said it was good quality.
Strongly recommended
This is a quality product for the price. All the pieces feel substantial and well made. Now it is installed, it looks very, very nice. Strongly recommended to my friends.
2020-05-05 00:00:00
Really pleased with the quality of this shower tray, it looks great in our new bathroom
A good choice
Bit messy when cutting - although easy to cut.
Overall very pleased with it, the water flows freely, you can easily finish it with tiles
Overall very pleased with it, the water flows freely, you can easily finish it with tiles
Good quality and easy to use
It fitted well under the shower screen and was easy to fit. Thank you very much.
good price