Showerlay Wiper 1200 x 1200 mm Line Invisible
Warning: Last items in stock!
This product is not sold individually. You must select at least 1 quantity for this product.
Wet room Kit Showerlay Wiper 1200 x 1200 mm Line Invisible is a walk in shower tray with end linear drain. Board can be 20, 30 or 40 mm thick, is sloped towards the drain, provides great acoustic insulation and is also lightweight while very strong. It is suitable both for concrete and timber floors. Shower area should be covered entirely, including drain grating, with finish material. The only visible features are the gaps in the floor through which the water drains
We include the longest linear shower channel to this walk in shower flooring - 1200 mm long stainless steel channel. It is integrated with the tray during the production process and comes with watertight seal. 70 mm wide stylish grate cover and comlpete siphon trap with capacity of 26 l/min and 20 mm high water seal arrive with the former. Grate is flushed with the frame, so there is no requirement for finish material height, although channel protrudes below the bottom shower tray surface for 10 mm. Steel is finished with brush, which is practical and particularly suitable for most architectural applications. Special degreasing cloth is included to clean the steel surfaces before gluing the finished floor surface. It's the longest linear gully we include to our wet room kits so it can be considered most luxurious.
Largest square shower tray 1200 x 1200 mm can accomodate bigger shower areas and create comfortable and easily accesible shower. This size kit isn't for smallest bathrooms, but has the longest drain integrated providing modern look. The floor is then a single expanse, with only a drainage hole visible, giving a space-enhancing seamless look.
|Size||1200 x 1200 mm|
|Channel length||900 mm|
|Thickness||20 · 30 · 40 mm|
|Trimming||Both sides: up to 50 mm.|
|Material||XPS foam sheet|
|Reinforcement||Fibre glass mesh & cementous glue.|
|Fall||4-way 2% towards the drain|
|Cleaning||From above (Easy clean system)|
|Set consists||Wet room tray · integrated linear drain body · drain grating · siphon trap|
If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 35 mm thickness might also be a good choice . Wet room kit timber floor fitting instructions
If case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions
In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.
To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.
The MAGNUM Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.
Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.
In some situations the digital regulation is not required and so the preference is for a simple on/off operation. Specifically industrial applications where the heating must remain on at all times. Therefore MAGNUM has designed the Standard Control: a simple on/off thermostat with temperature regulation that is clearly easy to operate.
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
What's the difference between this and the Ponente?
Invisible drain is suitable for the following materials: marble, vinyl floor, gres, hardened glass or exotic wood. In this drain, the level of the grating and the flange is the same, flush with the floor. There's no limit to the thickness of the finishing material. However, the surface of the drain must always be covered with some finishing material.
Regarding shower tray with the Premium Ponente drain, the grating and the flange aren't on the same level. There's a 15 mm difference between them and the grating itself is the final look, because it shouldn't be covered with finishing material. This is perfect drain for tiled floors, with tiles of standard thickness due to the lip, thanks to which you can nicely and easily finish the edges between the flange and the cover. Ponente is plain stainless steel pattern without any holes, solid bar of brushed steel.
If you have any questions I will be happy to assist.
020 7193 0953
Are these in stock for next day delivery please? https://wetroomsdesign.co.uk/wet-room-kit-1200-x-1200-line-invisible
We should be able to deliver them on next business day (Monday) if you order them soon today.
If you require more than few, please let me know how many and I will reply with our quotation and information about possible delivery date.
David 020 7193 0953