Showerlay Wiper 900 x 900 mm Point Ponente
Warning: Last items in stock!
This product is not sold individually. You must select at least 1 quantity for this product.
Wet room Kit Showerlay Wiper 900 x 900 mm Point Ponente is a walk in shower tray with steel square drainage. Square shaped drain is already integrated with the tray, under the layer of cement based glue. Outlet can be centred, offset or in the corner, giving a lot of flexibility. Wet room former is available in 3 thicknesses, is suitable for timber or concrete based floors.
Ponente shower gully is integrated with this walk in shower flooring, it's the most plain and simple stylish grate for wet room kits with square drain. Cover is circular and allows the drain to be opened to access the siphon trap from above. Waste trap with water seal of 20 mm manufactured by McAlpine comes along the board and drain. Water capacity of this kit is 26 l/min.
Wet room kit 900 x 900 mm is second smallest square tray former in our store. Save space with wetroom, with the average UK bathroom not much bigger than a king-sized bed, a wet room can be an ideal space-saving solution.
4-way sloped wet room tray always comes with integrated stainless steel channel. It is waterproofed during the manufacturing process. Board can be 20, 28 or 35 mm thick. Thicker tray is steeper but requires more space, while even 20 mm thick tray provides sufficient slope. In addition to that, thicker tray provides better accoustic and heating insulation.
Thickness: 20 mm
Compression fitting McAlpine waste trap with 26 l/min throughput, 20 mm water seal and 1.5 inch pipe diameter. Requires only 65 mm of space underneath the tray. Fully rotatable and adjustable.
Flow rate: 26 l/min
Easy to use set of ready-mixed sealing materials suitable for waterproofing floor and walls. Contains 4kg of PCI Lastogum tanking paint, 1l of primer, 10m sealing tape, 2 corners and 2 pipe collars per 3 m². Should be used to seal the joints between the floor and walls and to waterproof the drainage. Can be used for entire bathroom insulation. Not required if you have your own waterproofing materials, otherwise very useful and recommended.
Size: not included
Complete Magnum Underfloor heating set, including mat, advanced thermostat, floor sensor and fitting instructions. Fully suitable with our other products. Appropriate thermostat allows to set desired temperature of the floor.
Magnum Underfloor heating mats are available in several sizes. Mats can be shaped but but the heating cable cannot be cut, therefore it is advised to buy smaller than required heated area. Stationary elements like bath or furniture should be excluded from calculations. The cables are fully earth sheathed.
Size: not included
|Size||900 x 900 mm|
|Channel size||120 x 120 mm|
|Thickness||20 · 30 · 40 mm|
|Trimming||Both sides: up to 50 mm.|
|Material||XPS foam sheet|
|Reinforcement||Fibre glass mesh & cementous glue.|
|Fall||4-way 2% towards the drain|
|Cleaning||From above (Easy clean system)|
|Set consists||Wet room tray · integrated square drain body · drain grating · siphon trap|
If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 35 mm thickness might also be a good choice. Wet room kit timber floor fitting instructions
In case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions
In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.
To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.
The MAGNUM Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.
Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.
In some situations the digital regulation is not required and so the preference is for a simple on/off operation. Specifically industrial applications where the heating must remain on at all times. Therefore MAGNUM has designed the Standard Control: a simple on/off thermostat with temperature regulation that is clearly easy to operate.
what is the maximum make up that can go ontop for the drain to still work. I potentially have 15mm , would this work?
15 mm is the maximum thickness of all material that you would install on top of the tray.
Same tray with tileable cover accepts up to 20 mm floor finish material thickness, available here:
Alternatively we do have other drain types, available only in linear version, which do not have any restriction for finish material thickness at all, you can see them here:
I would be happy to assist if you have any questions.
David 020 7193 0953