Showerlay Wiper 900 x 1500 mm Point Sirocco

Wet room Kit Showerlay Wiper 900 x 1500 mm Point Sirocco

is a walk in shower tray with steel square drainage. Square shaped drain is already integrated with the tray, under the layer of cement based glue. Outlet can be centred, offset or in the corner, giving a lot of flexibility. Wet room former is available in 3 thicknesses, is suitable for timber or concrete based floors.

Drain integrated with this walk in former is square shaped, 120 mm x 120 mm. Sirocco grating with a pattern of regular squares as well as McAlpine 65 mm high, 26 l/min capacity and 20 mm water seal waste trap are included. Every part is assembled with the other one tightly making installation easy and usage of the tray safe and long lasting.

Wet room shower tray 900 x 1500 mm for tiled floor is a popular size for spacious bathroom. Large format tiles can be used to create more seamless, elegant look. Refurbish your old bathroom into inspirational and practical shower room no matter if you have timer or concrete floor.

More details

New

£ 264.34

Tax included

£ 310.99

-15%

  • Not include
  • 3 m²
  • 6 m²
Waterproofing kit is used to seal shower tray as well as connections between walls and floor. It is recommended for concrete and mandatory for timber flooring. Each kit contains: 4kg tanking liquid, 1l primer, 10m sealing tape, 2 corners, 2 pipe collars. One kit covers 3 m² with 2 coats. If you buy it as addition to any drain or wet room kit You save £40 if you buy kit that covers 3 m² or £80 if buy one which covers 6 m².
  • 20 mm
  • 28 mm
  • 35 mm
Thickness of the board on the edges. It has 2% gradient on the entire upper surface and is shallower near the drain. As there's always 2% fall, slope is larger the thicker wet room kit is.
  • Central
  • Corner
  • Offset

Question will be displayed after moderation.
Send to a friend

Product information will be sent to given address.

* Required fields

Cancel

Size900 x 1500 mm
Channel size120 x 120 mm
Grate styleSirocco
Height1500 mm
Width900 mm
Thickness20 · 30 · 40 mm
TrimmingBoth sides: up to 50 mm.
MaterialXPS foam sheet
ReinforcementFibre glass mesh & cementous glue.
Fall2% towards the drain
AdditionalsTanking kit
Drain surfacebrush
CleaningFrom above (Easy clean system)
ModelPoint
Set consistsWet room tray · integrated square drain body · drain grating · siphon trap
  • Dimensions as described on equivalent technical drawings,
  • Both sides can be trimmed without any harm, using regular handsaw,
  • Make sure you cut it for equal distances from both sides to preserve pre-made fall to the drain,
  • Drain channel is positioned central, offside or in corner, depending option the customer selects.
  • Designed especially for range of Wiper WP120 Premium drains,
  • Square traps are built into the tray during the manufacturing process,
  • Our showerlay is a 20/28/35 mm XPS foam sheet covered on both sides with a flexible cementous glue and reinforced with a fibre glass mesh,
  • The showerlay is CNC machine cut to give a perfect pre-formed fall from each corner to the drain,
  • It is lightweight but very strong,
  • Perfect solution for British wooden floors but can also be used on concrete floors. When it is used on wooden floors,the floor must be underboarded after floor boards have been removed,
  • Standard and minimal underboarding should be 20 mm thick,
  • Ideal for tiled floors. Because of the high compressive strength of the XPS foam, it can even be used with small mosaic tiles. This is not suitable for vinyl floor coverings,
  • The shower lay can be easily cut on site should you have any obstacles such as pipe boxings,
  • Easy to use with under floor heating systems (should be installed on top of the shower tray)
  • One hundred per cent, double waterproofing,
  • Hardness of the surface layer allows to cement even very small mosaics,
  • High acoustic and thermal insulation,
  • After installation, the plates should be supported beneath entire surface.
  • Product is suitable for:
    Timber floor Concrete floor Tiles Mosaic
    Wet room kit advantages

Our wet room kits are available in three thicknesses: 20, 28 and 35 mm. Depending on space, floor type, and desired gradient you can choose best option for you.

If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 35 mm thickness might also be a good choice. Wet room kit timber floor fitting instructions

In case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions

In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.



Wet room kit 900 x 1500 technical drawing

The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.

For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.

Tanking kit contains:

  • 4kg Tanking Liquid
  • 1l Primer
  • 10 Metres flexible Sealing Tape
  • 2 Flexible Pipe Collars
  • 2 Corners

Features:

  • Consumption to 1,2kg/m²
  • Solvent free
  • Drying time: 2h

Tanking liquid

Tanking liquidThe tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.

Primer

Tanking primerThe product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.

10m sealing tape · 2x flexible pipe collars · 2x corners

Tanking mattPipe collarCorner

Shower trays incorporate square drain built-into the tray during the manufacturing process. WP120 is the medium drain available in this range. The top surface of the drain is 3 mm stainless steel 120 x 120 mm consisting of the frame and grating. The product has many variations making it very flexible to suit all possible situations in the shower.

  • Made of high quality stainless steel
  • Size: 120 x 120 [mm]
  • Total height (H): 88 [mm]
  • Height (G): 68 [mm]
  • Tile channel depth (A): 12 [mm]
  • Tile channel dimensions: 114 x 114 [mm]
  • Throughput: 26/50 [l/min]
  • Insulating flange included
  • Sealing membrane included
  • Surface finish: mirror, mat, brushed
  • High quality McAlpine poly propylene siphon trap
  • Complete siphon, pipe diameter: 1.5" (british standard size),
  • Pipe height adjustable and rotatable at 360°,
  • Drain's cover is included.
WP120 Premium

Grating patterns available for this product:

Suitable for:

  • Wet rooms,
  • Showers,
  • Bathrooms,
  • Wooden floors,
  • Mosaic floors,
  • Concrete floors,
  • Screed floors,
  • Tiled floor surface,
  • Wheelchair use,

Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.

Showerlay installation 20 mm technical drawing 30 mm technical drawing 40 mm technical drawing Long term guaranteeSiphon technical drawing

Conventional floor boards are approx 20mm thick so laying the tray on top of the joists would bring the top of the tray level with the floor boards. We do not recommend tiling straight on to floor boards. We recommend that the entire wooden floor is covered in a 10mm thermal tile backer board prior to tiling and therefore you may need to insert a 10mm packer under the Showerlay to achieve an even level floor area throughout. The tile backer board is a good insulator and the perfect material on which to tile.

If required the tray can be installed on a raised platform.


The position of the drain exit is determined by the installer on site as the drain is cut into the trough by the user and thus can avoid joists or support beams. The base of the tray is totally flat and is installed onto the wooden joists in the normal manner with support between the joists. It has fully adjustable drain and grid to accommodate various tile heights

It can be installed by any competent DIY person and as the drain trough is already installed into the tray cuts down on install time.