Showerlay Wiper 800 x 1500 mm Point Mistral

51200

Waterproofing kit is used to seal shower tray as well as connections between walls and floor. It is recommended for concrete and mandatory for timber flooring. Each kit contains: 4kg tanking liquid, 1l primer, 10m sealing tape, 2 corners, 2 pipe collars. One kit covers 3 m² with 2 coats.

Thickness of the board on the edges. It has 2% gradient on the entire upper surface and is shallower near the drain. The benefit of thicker tray is steeper slope, although even the shallowest trays have sufficient slope for water to flow towards the drain, no matter where it drops.

Complete Magnum Underfloor heating set, including mat, advanced thermostat, floor sensor and fitting instructions. Fully suitable with our other products. Appropriate thermostat allows to set desired temperature of the floor.

Magnum Underfloor heating mats are available in several sizes. Mats can be shaped but the heating cable cannot be cut, therefore it is advised to buy smaller than required heated area. Stationary elements like bath or furniture should be excluded from calculations. The cables are fully earth sheathed.

Delivery:Free | 1-3 working days
Payment:Card | Over the phone | PayPal | BACS
Returns:30 days return right
Support:020 7193 0953 • 017 0927 3601

£ 239.69

tax incl.

£ 281.99 tax incl. -15%

Trade discount policy:bulk orders and returning customers

Save for later

Send to a friend

Send product information

Basic product info and a link to a product will be sent to a person specified above.

Where should we reply to?

We will do our best to reply as fast as possible.

Wet room Kit Showerlay Wiper 800 x 1500 mm Point Mistral is a walk in shower tray with steel square drainage. Square shaped drain is already integrated with the tray, under the layer of cement based glue. Outlet can be centred, offset or in the corner, giving a lot of flexibility. Wet room former is available in 3 thicknesses, is suitable for timber or concrete based floors.

Square drainage WP120 Premium is included to the tray, properly fitted and waterproofed. Mistral grate style has pattern of variously sized circular holes, regularly filling the visible metal surface after the installation. Brushed finish for steel is not only glossy but also very practical. To make it a complete product, we include McAlpine waste siphon trap, suitable for every standard bathroom.

Walk in 800 x 1500 shower tray is rectangle mid-sized trendy corner wet room kit. Modern and becoming more popular in Britain it encases all functions of showers in one accessible space. Create a trendy, stunnig and luxury bathroom while retaining full shower functionality and increase value of your home.

If you buy this product you will receive (parts included):

Size800 x 1500 mm
Channel size120 x 120 mm
Grate styleMistral
Height1500 mm
Width800 mm
Thickness20 · 30 · 40 mm
TrimmingBoth sides: up to 50 mm.
MaterialXPS foam sheet
ReinforcementFibre glass mesh & cementous glue.
Fall4-way 2% towards the drain
AdditionalsTanking kit
Drain surfacebrush
CleaningFrom above (Easy clean system)
ModelPoint
Set consistsWet room tray · integrated square drain body · drain grating · siphon trap
    • Dimensions as described on equivalent technical drawings,
    • If needed, the tray can be easily shortened in its length or width, using a handsaw,
    • Make sure you cut it for equal distances from both sides to preserve pre-made fall to the drain,
    • Drain channel is positioned central, offside or in corner, depending option the customer selects.
    • Designed especially for range of Wiper WP120 Premium drains,
    • Square traps are built into the tray during the manufacturing process,
    • Our showerlay is a 20/28/35 mm XPS foam sheet covered on both sides with a flexible cementous glue and reinforced with a fibre glass mesh,
    • The showerlay is CNC machine cut to give a perfect pre-formed fall from each corner to the drain,
    • It is lightweight but very strong,
    • Perfect solution for British wooden floors but can also be used on concrete floors. When it is used on wooden floors,the floor must be underboarded after floor boards have been removed,
    • Standard and minimal underboarding should be 20 mm thick,
    • Ideal for tiled floors. Because of the high compressive strength of the XPS foam, it can even be used with small mosaic tiles. This is not suitable for vinyl floor coverings,
    • The shower lay can be easily cut on site should you have any obstacles such as pipe boxings,
    • Easy to use with under floor heating systems (should be installed on top of the shower tray)
    • One hundred per cent, double waterproofing,
    • Hardness of the surface layer allows to cement even very small mosaics,
    • High acoustic and thermal insulation,
    • After installation, the plates should be supported beneath entire surface.
Product is suitable for:
Timber floor Concrete floor Tiles Mosaic

Wet room kit advantages

Our wet room kits are available in three thicknesses: 20, 28 and 35 mm. Depending on space, floor type, and desired gradient you can choose best option for you.

If you have timber floor - existing floor board thickness. Usually they are 20 or 28 mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up floor, 35 mm thickness might also be a good choice. Wet room kit timber floor fitting instructions

In case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions

In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be underboarded beneath entire surface either with ply or solid concrete. The biggest difference between thicknesses is the slope's angle achieved after installation is completed and shower tray tiled.



Wet room kit 800 x 1500 technical drawing

The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.

For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.

Tanking kit contains:

  • 4kg Tanking Liquid
  • 1l Primer
  • 10 Metres flexible Sealing Tape
  • 2 Flexible Pipe Collars
  • 2 Corners

Features:

  • Consumption to 1,2kg/m²
  • Solvent free
  • Drying time: 2h

Tanking liquid

Tanking liquidThe tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.

Primer

Tanking primerThe product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.

10m sealing tape · 2x flexible pipe collars · 2x corners

Tanking mattPipe collarCorner

Complete Underfloor Heating Kit

It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.

To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.

MAGNUM Underfloor Heating

The MAGNUM Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.

Heating mat

Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.


Underfloor heating mat technical properties:

  • EMC-free 2-conductor cable fitted to fibre-optic net
  • 2.5 meter 3-core supply cable
  • Fully encased in an aluminium earthed sheath
  • Unique blind connection between the heating and the connection cable
  • Chrome/Nickel resistance wire
  • PTFE (Teflon) insulation
  • PVC protective sheath
  • 10 -11 watt per meter resistance wire, 230 Volt
  • Cable diameter approximately 4 mm
  • Mat widths of 25 or 50 cm
  • Complies with current NEN standards for installation in completely wet rooms

Underfloor Heating Mat

Thermostat

In some situations the digital regulation is not required and so the preference is for a simple on/off operation. Specifically industrial applications where the heating must remain on at all times. Therefore MAGNUM has designed the Standard Control: a simple on/off thermostat with temperature regulation that is clearly easy to operate.

Specification:

  • Voltage: 230 Volt - 50/60 Hz
  • Maximum load: 16A / 230 V
  • Temperature range: +5 to +40°C
  • Housing: IP21
  • Color: Polar white (RAL 9010)
  • Testing: CE
  • Technical details:
  • On/off thermostat complete with temperature regulation
  • Including floor sensor
  • Integral room sensor and floor limit sensor
  • Multi frame adapter system for: Gira, Jung, Elko, Merten, Busch Jager, etc.
Underfloor Heating Thermostat

Shower trays incorporate square drain built-into the tray during the manufacturing process. WP120 is the medium drain available in this range. The top surface of the drain is 3 mm stainless steel 120 x 120 mm consisting of the frame and grating. The product has many variations making it very flexible to suit all possible situations in the shower.

  • Made of high quality stainless steel
  • Size: 120 x 120 [mm]
  • Total height (H): 88 [mm]
  • Height (G): 68 [mm]
  • Tile channel depth (A): 12 [mm]
  • Tile channel dimensions: 114 x 114 [mm]
  • Throughput: 26/50 [l/min]
  • Insulating flange included
  • Sealing membrane included
  • Surface finish: mirror, mat, brushed
  • High quality McAlpine poly propylene siphon trap
  • Complete siphon, pipe diameter: 1.5" (british standard size),
  • Pipe height adjustable and rotatable at 360°,
  • Drain's cover is included.
WP120 Premium

Grating patterns available for this product:

Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.

Showerlay timber floor installationShowerlay concrete floor installation 20 mm technical drawing 30 mm technical drawing 40 mm technical drawing Long term guaranteeSiphon technical drawing

Opinions, reviews and tests for:
Showerlay Wiper 800 x 1500 mm Point Mistral
Average grade: 0
Ratings number: 0
5
0%
4
0%
3
0%
2
0%
1
0%
Do you own this product?
Leave product review to help other customers to make the right choice

Customer product reviews
Question will be displayed after moderation.

Typical questions asked about products:
How long is the delivery?
Is the product easy to fit?
Which options should I choose?