is stainless steel drainage without insulating flange. Length of 500 mm gives a lot of flexibility with installation and design of your wet room. It is recommended to be installed outside, or where the waterproof seal is not necessary. Swimming pools, terraces or garages are good examples of places where this drain can be fitted in. Manufactured of 304 stainless steel gives the product strength and corrosion resistance. It is not suitable for indoor wet areas, wooden floors, although can be cast into concrete screeded floor. Channel is 30 mm high and total height with waste trap is 98 mm. It's the cheapest linear shower drain in our store.
Width of Classic drainage channel is 8 cm and it has included Sirocco which is considered to be the most practical pattern, with 3 rows of square shaped holes running parallelly to cover edge and 64 mm wide, grate is 494 mm long. During installation, you need to create support below the entire channel and you can set the height it protrudes above the floor surface. It allows you to adjust the lip height to match your tiles thickness. To ensure the drain works properly, surrounding area should be sound and tanked.
65 mm high Mc Alpine siphon trap with pipe is also included to drain. It features capacity of 26 l /min and water seal 20 mm high. Trap can be opened from above, even after the installation is completed, after lifting up the grate to allow easy cleaning.Standard 1.5'' pipe is in the same pack, allowing instant connection to your waste system.
Warning: Last items in stock!
|Channel length||500 mm|
|Channel height||30 mm|
|Total height||98 mm|
|Channel width||84 mm|
|Total width||84 mm|
|Material||304 S 15 grade stainless steel|
|Additionals||Tanking kit, Adjustable legs|
|Drain surface||mirror · brush · matt|
|Shower waste||Plastic (PCV)|
|Steel collar||Not integrated|
|Cleaning||From above (Easy clean system)|
|Set consists||Linear drain body · drain grating · siphon trap|
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
You can add the Adjustable legs to your order. If you select this option, you will receive two parts that can be attached to the edges of linear drain and used to adjust total height of the drain with siphon. We will send them in the same package as the drain.
They are not necessary though, and anything can be used to raise the drain. Usually the installator or the plumber decides if they are required or not.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
Typical questions asked about products:
How long is the delivery?
Is the product easy to fit?
Which options should I choose?