Linear drain Wiper 500 mm Classic Pure

Linear gully Wiper 500 mm Classic Pure

is stainless steel drainage without insulating flange. It is recommended to be installed outside, or where the waterproof seal is not necessary. Swimming pools, terraces or garages are good examples of places where this drain can be fitted into. Manufactured of 304 stainless steel gives the product strength and corrosion resistance. It is not suitable for wooden floors, although can be cast into concrete screeded floor. Channel is 30 mm high and total height with waste trap is 98 mm. It's the cheapest linear shower drain in our store.8 mm. It's the cheapest linear shower drain in our store.

Width of Classic drainage channel is 8 cm and it has included Pure tile able grate, which is 12 mm deep and 64 mm wide, grate is 494 mm long. During installation, you need to create support below the entire channel and you can set the height it protrudes above the floor surface. It allows you to adjust the lip height to match your tiles thickness. To ensure the drain works properly, surrounding area should be sound and tanked.

65 mm high Mc Alpine siphon trap with pipe is also included to drain. It features capacity of 26 l /min and water seal 20 mm high. Trap can be opened from above, even after the installation is completed, after lifting up the grate to allow easy cleaning. Standard 1.5'' pipe is in the same pack, allowing instant connection to your waste system.

More details

New

£ 133.70

Tax included

£ 167.12

-20%

  • Not include
  • 3 m²
  • 6 m²
Waterproofing kit is used to seal shower tray as well as connections between walls and floor. It is recommended for concrete and mandatory for timber flooring. Each kit contains: 4kg tanking liquid, 1l primer, 10m sealing tape, 2 corners, 2 pipe collars. One kit covers 3 m² with 2 coats. If you buy it as addition to any drain or wet room kit You save £40 if you buy kit that covers 3 m² or £80 if buy one which covers 6 m².

Save for later

Question will be displayed after moderation.
Send to a friend

Product information will be sent to given address.

* Required fields

Cancel

Channel length500 mm
Grate stylePure (slot)
Channel height30 mm
Total height98 mm
Channel width84 mm
Total width84 mm
Material304 S 15 grade stainless steel
AdditionalsTanking kit, Adjustable legs
Drain surfacemirror · brush · matt
SiphonPlastic (PCV)
Steel collarNot integrated
CleaningFrom above (Easy clean system)
ModelClassic
Set consistsLinear drain body · drain grating · siphon trap
  • Length (X): 500 [mm]
  • Height of channel (C): 30 [mm]
  • Height to the centre of waste pipe (G): 68 [mm] (can be adjusted)
  • Total height (H): 98 [mm]
  • Width of channel (Y): 84 [mm]
  • Complete siphon, pipe diameter: 1.5" (british standard size),
  • Pipe height adjustable and rotatable at 360°,
  • Drain's cover included.
  • Pure drain cover is an internal container that you can insert the tiles into. This type of drain is 100% tile-able.

  • Tile channel depth (A): 12 [mm]
  • Tile channel width (D): 60 mm [mm]

Grating patterns available for this product:

Linear drain gratings

Linear shower drain advantages

The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.

For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.

Tanking kit contains:

  • 4kg Tanking Liquid
  • 1l Primer
  • 10 Metres flexible Sealing Tape
  • 2 Flexible Pipe Collars
  • 2 Corners

Features:

  • Consumption to 1,2kg/m²
  • Solvent free
  • Drying time: 2h

Tanking liquid

Tanking liquidThe tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.

Primer

Tanking primerThe product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.

10m sealing tape · 2x flexible pipe collars · 2x corners

Tanking mattPipe collarCorner


Adjustable legsYou can add the Adjustable legs to your order. If you select this option, you will receive two parts that can be attached to the edges of linear drain and used to adjust total height of the drain with siphon. We will send them in the same package as the drain.

They are not necessary though, and anything can be used to raise the drain. Usually the installator or the plumber decides if they are required or not.

We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals. 

The waste trap provides Water Seal that prevents any bad smells to get back to your shower.

  • Colour: white,
  • Total height: 61,50 mm,
  • Waste pipe diameter: 1.5" (british standard size)
  • Water seal: 20mm
  • Flow rate [l/min]: 26/50 (for a 15mm/120mm liquid column)
  • Ready to be connected to waste system
  • Additional info: Waste Grid and Dip Tube removable from top to facilitate easy cleaning. All McAlpine Shower Traps with top access surpass the minimum required flow rate of 24 litres per minute when tested in accordance with clause 5 of BS EN 274-2:2002

Suitable for:

  • Wet rooms,
  • Showers,
  • Bathrooms,
  • Outdoor drainage,
  • Concrete floors,
  • Screed floors,
  • Tiled floor surface,
  • Wheelchair use,

Documents available below are available to everybody for free to download. They can be open in high quality on your computer and be printed for further use.

 Wiper Classic technical drawingSiphon technical drawing  Long term guarantee

30 Similar products