Linear drain Wiper 1100 mm Classic Sirocco
Warning: Last items in stock!
This product is not sold individually. You must select at least 1 quantity for this product.
Linear gully Wiper 1100 mm Classic Sirocco is stainless steel drainage without insulating flange. This drain is 1100 mm long, which is the second largest rectangle unit in our offer. It is recommended to be installed outside, or where the waterproof seal is not necessary. Swimming pools, terraces or garages are good examples of places where this drain can be fitted in. Manufactured of 304 stainless steel gives the product strength and corrosion resistance. It is not suitable for indoor wet areas, wooden floors, although can be cast into concrete screeded floor. Channel is 30 mm high and total height with waste trap is 98 mm. It's the cheapest linear shower drain in our store.
Width of Classic drainage channel is 8 cm and it has included Sirocco which is considered to be the most practical pattern, with 3 rows of square shaped holes running parallelly to cover edge and 64 mm wide, grate is 1094 mm long. During installation, you need to create support below the entire channel and you can set the height it protrudes above the floor surface. It allows you to adjust the lip height to match your tiles thickness. To ensure the drain works properly, surrounding area should be sound and tanked.
Convenient siphon trap with 26 l /min draining speed and 20 mm tall water seal is the last element always included to every drain. Made of PVC is very flexible as it can be rotated and pipe's height can be adjusted, making installation easier. It is Mc Alpine product so should be suitable for any wet room pipework. It can be opened even after installation is over for easy cleaning.
|Channel length||1100 mm|
|Channel height||30 mm|
|Total height||98 mm|
|Channel width||84 mm|
|Total width||84 mm|
|Material||304 S 15 grade stainless steel|
|Additionals||Tanking kit, Adjustable legs|
|Drain surface||mirror · brush · matt|
|Waste trap||Plastic (PCV)|
|Steel collar||Not integrated|
|Cleaning||From above (Easy clean system)|
|Set consists||Linear drain body · drain grating · siphon trap|
The ISOL-ONE sealing mat is made from a polyethylene film coated with a special non-woven fabric on both sides, so that it bonds with the glue layer. Its installation is recommended in all areas that require sealing. The mat is resistant to the cracking of the substrate, ensures the seal up of the entire surface, reduces installation time, allowing to lay the tiles immediately after gluing the mat.
Adjustable feet are two small metal parts that can be connected to each channel end. They allow you to precisely set the unit height and level. Thanks to the red caps you can anchor the drain to the floor. They are part of unit, included in price and always added to each drain.
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
It is possible to include a complete Underfloor Heating Kit to your order. All you need to do is to choose the required size. Additional package, with heating mat, appropriate thermostat, sensor and instructions will be dispatched together with the other goods.
To calculate required mat size you need to get square coverage of the floor and exclude any permanent / fixed fixtures from them. It is also recommended to buy slightly smaller mat than calculated size - you can shape it but cannot cut the cables, therefore too large mat could not be installed.
The MAGNUM Electric Heating Mat is a unique type of floor heating mat. The system has been designed to be used on an existing tiled floor or an existing finished floor, so that floor heating can still be installed there. The mat is approximately 4 mm thick and can be included in a layer of adhesive without any demolishing or grinding. The mat fits virtually underneath the surface. This decreases the heating time of the floor, that also makes this system suitable for rooms that are not permanently occupied including bathrooms, studies, playrooms, etc.
Underfloor heating mat set consists of all necessary parts for installation. One Thermostat is needed for every 23 m² of heating mat. It is included as optional, to allow ordering mat for custom areas, for example if you need 13 m² of mat total, you should buy 10 m² with one of the thermostats set as include and 3 m² with thermostat not included. In case you require less mat coverage than possible to buy from our product pictures, for example 14.5 m² you should always round low with your purchase and buy 14 m² as the mat is impossible to cut. It can be shaped but not shortened to size.
In some situations the digital regulation is not required and so the preference is for a simple on/off operation. Specifically industrial applications where the heating must remain on at all times. Therefore MAGNUM has designed the Standard Control: a simple on/off thermostat with temperature regulation that is clearly easy to operate.
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
Typical questions asked about products:
How long is the delivery?
Is the product easy to fit?
Which options should I choose?