is a walk-in tray with a linear drain. The shower tray is characterised by a one-way single slope contoured towards the drain channel. In case of a type of floor and the size of the slope we want, there
The set consists of a OneWay Showerlay with integrated and waterproofing linear drain. Dimensions of drain channel: 500mm long and 80mm wide. This set comes also with
800 x 800 tray is one of the smallest
Warning: Last items in stock!
Duschboard inkl. Rinne
Stärke: 30 mm
Flow rate: 26 l/min
Größe: nicht mitbestellen
|Size||800 x 800 mm|
|Channel length||500 mm|
|Grate style||Pure (slot)|
|Thickness||30 · 40 mm|
|Trimming||Shorter side: up to 50 mm · Longer: up to 100 mm.|
|Material||XPS foam sheet|
|Reinforcement||Fibre glass mesh & cementous glue.|
|Fall||1-way 2% towards the drain|
|Cleaning||From above (Easy clean system)|
|Set consists||Wet room tray · integrated linear drain body · drain grating · siphon trap|
We supply McAlpine CD-HC26-65 PCV (polypropylen) waste trap with our drains. To clean them you can simply dismantle it from above when installed, and waterflow will remove any dirt. If not you can use chemicals.
The waste trap provides Water Seal that prevents any bad smells to get back to your shower.
If you have timber floor - existing floor board thickness. Usually they are 30mm thick, in that case you should go for adequate thick wet room kit, to avoid floor height increase and step ups. If you want to achieve stepped up
In case of concrete floor, every thickness is suitable, if you're going to screed the floor you need to shutter the future shower area off and leave proper space for tray to be inserted in the future. If screed has already been done, you will need to use jackhammer or similar tool to groove exact tray thickness and shape when the shower is going to be created. Wet room kit concrete floor fitting instructions
In case of both floor types, every shower tray thickness is enough to bear human weight, as it needs to be
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals. Should not be used in places exposed to pressurised water, for an instance swimming pools. Ready to use, no mixing required and easy to apply with a roller. The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc. The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For anti-moisture insulation systems in wet rooms and rooms intended for human residence. The tanking liquid is a ready-to-use singlecomponent, solvent-free sealant composed of polymer dispersion, fillers and modifying additives. When applied to the surface, upon binding it creates a flexible and water-insulating layer.
The tanking liquid is a ready to use, single component, solvent-free sealant mass, consisting of polymer dispersion, fillers and additives. When applied to a substrate and cured, it forms a flexible waterproofing coating. The product is intended for use inside places intended for human residence, especially in humid areas (such as bathrooms, kitchens, laundries), to perform insulation against moisture under linings and coverings, such as ceramic tiles, glazed tiles, terracotta, wooden floors and panels, and synthetic carpets.
The product is intended for priming absorbent and porous surfaces, inside and outside buildings. It is especially recommended for cement - limestone plaster, gas concrete, plaster-carton boards and cement plaster. The primer has a high penetration ability, is deeply absorbed into the substrate, thus strengthening it, while allowing for „breathing”. These benefits improve the structure of the substrates, which, due to the passage of time, have lost their appropriate parameters. The priming solution improves adhesion to the surface of other materials that will be used on the primed substrate. By reducing the absorbency of the substrate, the wear of the applied coating materials, emulsion paints, glues, mineral putties reduces as well. The solution, due to the content of the biocide and fungicide, protects the primed substrate against the formation of mold and bacteria in the product.
I am trying to visualise how the oneway fall product will look at the edges- where the slope towards the drain meets the rest of the bathroom floor is there a triangular space that will require tiling/trimmed? Or does it end up flush with the rest of the floor somehow? Thanks
OneWay wet room trays slope from 30 or 40 mm to 18 mm thickness on the other end. It means that the thicker end should be flushed with rest of the floor in your bathroom, while the opposite side will be lower by 12 or 22 mm.
There will be triangular space on the side of the tray which should be tiled on. Shower screen usually is installed right above it.
If you require further assistance please let me know.
David M 020 7193 0953