Joint grout PCI Nanofug® Premium 5 kg View larger

Joint grout PCI Nanofug® Premium 5 kg


Delivery:Free | 1-3 working days
Payment:Card | Over the phone | PayPal | BACS
Returns:30 days return right
Support:020 7193 0953 • 017 0927 3601

£ 42.99

tax incl.

Trade discount policy:bulk orders and returning customers

Save for later

Send to a friend

Send product information

Basic product info and a link to a product will be sent to a person specified above.

Where should we reply to?

We will do our best to reply as fast as possible.

Multi-use flexible joint grout especially for fully vitrified tiles and vitrified tiles.

Flexible, fast setting, cementitous mortar for grouting ceramic floor or wall finishing materials and for glass floors and walls exposed to heavy mechanical load stresses caused by changes of temperature. Destinated for balconies, terraces and facades, for stone tiles resistant for discolouration. Class CG2WA according to EN 13888.
  • Grout width: 1-10 mm
  • Grout width with aggregate: up to 50 mm
  • Working convenience: approx. 40 minutes
  • For indoor and outdoor use
  • Easy-to-clean effect
  • Fine surface with beautiful colouring
  • Shelf life: 12 months.

Material baseDry grout mix with elastifying polymers. No injurious silica dust during the application.
ComponentsSingle component
Packaging size5 kg pail
Storagemin. 12 months when stored in dry conditions, no permanent storage over +30°C
Gauging water for 1 kg powderapprox. 230 ml approx. • 270 ml for colour white • approx. 190 ml for colour black
Slake timeapprox. 3 minutes
Walkable afterapprox. 2 hours
Able to bear weight afterapprox. 24 hours
Temperature resistance-20°C to +80°C
Joint width1 to 10 mm, from 10 mm to be blended with 25% of silica sand F 32 (0.1 to 0.4 mm)
Tiles 30 x 30 cm (at joint width 5 mm and depth 8 mm)Consumption approx. 400 g/m² • 5 kg pail covers approx. 12.5 m²
Tiles 20 x 20 cm (at joint width 5 mm and depth 8 mm)Consumption approx. 600 g/m² • 5 kg pail covers approx. 8.3 m²
Medium mosaic 5 x 5 cm (at joint width 2 mm and depth 6 mm)Consumption approx. 700 g/m² • 5 kg pail covers approx. 7.1 m²
Split tiles 24 x 11.5 cm (at joint width 8 mm and depth 10 mm)Consumption approx. 1500 g/m² • 5 kg pail covers approx. 3.3 m²
Gauging water for 5 kg pailapprox. 1150 ml • approx. 1350 ml for colour white • approx. 950 ml for colour black

Features and benefits:

  • Easy-to-clean effect for easier cleaning
  • Increased resistance against acidic household cleaners
  • Improved protection against certain mildew and microorganisms
  • High working convenience within approx 40 minutes
  • Rapid setting, but no hardening on the surface
  • Fine surface and brilliant colouring
  • Corresponds to CG2 WA to DIN 13888:2009
  • Very low emission, GEV EMICODE EC1 Plus R
  • Low in chromates

Fields of application:

  • For indoor and outdoor use
  • For walls and floors
  • For joint widths from 1 - 10 mm
  • Especially for fully-vitrified tiles, vitrified tiles, split tiles, porcelain mosaic, glass mosaic, glass tiles
  • Suitable for non-vitrified tiles
  • Suitable for natural stone insensitive to staining
  • In residential areas, bathrooms, showers, on balconies, terraces, facades, in public and commercial areas subject to frequent wetness, eg shower facilities, saunas, toilets In showrooms and presentation areas
  • On heated screeds, dry screeds, precast concrete elements, plasterboards, gypsum blocks, particle boards, wooden floorboards and areas subject to extreme variations in temperature

PCI Gisogrund improves the adhesion of plaster and lime gypsum plaster to brickwork.

PCI Gisogrund protects levelling compound and thin-bed mortar from too rapid dehydration, extends the open time, helps improve adhesion and prevents the formation of cracks caused by shrinkage.

Preparation of substrate

Immediately after setting the tiles rake joints clean to a uniform depth corresponding to the thickness of the tile. Allow adhesive to set.

Application procedure

  1. Pour gauging water (see mixing table) in a clean container. Add PCI Nanofug Premium and mix with a suitable paddle (e.g. from Collomix) attached to an electric drill until a plastic and lump-free consistency is obtained.
  2. Leave to stand for approx. 3 minutes and re-mix.
  3. Work grout into the joints using a rubber grouting float and allow to set. Grout one more time if necessary to achieve a flush joint. After the grout has set (finger test) clean tiles with a slightly damp sponge or sponge float.
  4. When the grout is dry remove the remaining film on the tiles with a damp sponge.

Please note:

  • Do not apply at temperatures below +5 °C and above +25°C or under exposure to direct heat, wetness and draught.
  • Higher temperatures reduce, lower temperatures increase the working time. Cover newly grouted areas outdoors with a foil to protect the surface from direct sunlight and strong draught.
  • Any underfloor heating must be switched off when grouting and during the curing process (min. 24 hours).
  • Should a white film remain visible on the ceramic tiles after hardening it can be removed after 2 to 3 days with the acidic cement stain remover PCI Zementschleier-Entferner sauer. Prewet joints and tiles thoroughly and wash with lots of water after cleaning. See the technical data sheet no. 816 for the application of PCI Zementschleier-Entferner sauer.
  • The joint might be affected when being intensively exposed to acidic cleaning agents or/and long action time of cement-attacking media. The joints should be thoroughly prewet before cleaning and washed off with lots of water after cleaning.
  • When grouting non-slip tiles or floor coverings with a rough surface the grout film must be thoroughly removed while still fresh (carry out trial grouting and/or trial cleaning).
  • In case of polished fully vitrified tiles, colour pigments might solidify in the micropores possibly found in the surface of the tile. We therefore advise against an intense colour contrast between tile and joint. In case of doubt carry out trial grouting.
  • We recommend to use a non-woven cloth to wash sharp-edged tiles.
  • It might require a higher effort when using the colour black.
  • Prevent PCI Nanofug from overflowing into perimeter joints and adjoining areas by taking appropriate measures such as placing temporary barrier strips before grouting. Remove strips before applying the elastic sealant. Seal joints between tiles, fitted elements and pipe culverts as well as corner joints and connection joints with the elastic sealant PCI Silcofug E or PCI Silcoferm S, use PCI Elritan 100 for facades.
  • We recommend to use the same batch number for the same project.
  • The original colour may change when mixing PCI Nanofug Premium with silica sand.
  • Never add water or wet grout and/or powder to reconstitute a grout mix which has already begun to set.
  • Do not use a dry cloth for cleaning as staining might be caused when rubbing hardened grout into the damp joint.
  • Grouting in swimming pools should be carried out with PCI Durafug NT or PCI Durapox NT/NT plus. Please contact the PCI Technical help-line.
  • Use PCI Durafug NT to grout in potable water tanks.
  • Shelf life: min. 12 months when stored in dry conditions, no permanent storage over +30°C.
  • Suitable tools are available from e.g. Collomix GmbH, Horchstraße 2, 85080 Gaimersheim/Germany,
  • Clean tools with water immediately after use; once cured product can only be removed by mechanical scraping.

02 Bahama beige

18 Manhattan

31 Cement grey

03 Carmel

19 Basalt

40 Black

05 Midbrown

20 White

41 Dark brown

11 Jasmin

21 Grey

43 Pergamon

12 Anemone

22 Sand grey

44 Topas

16 Silver grey

23 Light grey

47 Anthracite

49 Light brown

50 Red brown

51 Intensive brown

52 Beige brown

53 Ochre

Subject to deviations in colour due to print.

Opinions, reviews and tests for:
Joint grout PCI Nanofug® Premium 5 kg
Average grade: 0
Ratings number: 0
Do you own this product?
Leave product review to help other customers to make the right choice

Customer product reviews
Question will be displayed after moderation.

Typical questions asked about products:
How long is the delivery?
Is the product easy to fit?
Which options should I choose?